How to Remove Rear Drive Shaft on Can Am Outlander
Drive shaft giving yous problems and driving yous crazy?
Don't worry, nosotros are here to help you find out if you have a bulldoze shaft problem – once and for all!
Drive shaft are usually constitute between the gearbox and front wheels. With the constant twisting and harsh road conditions, drive shaft problems are common for vehicle with mileage above 120,000 kilometres. A worn bulldoze shaft volition manifests itself in the following symptoms:
- Spoiled or torn bulldoze shaft cover
- Clicking noise
- Vibration
If your machine is having any of these symptoms, you should consider getting your bulldoze shaft inspected and repaired.
- What is bulldoze shaft?
- How does it work?
- What is the tiptop 3 drive shaft problems?
- Spoiled or torn bulldoze shaft cover.
- Clicking noise
- Vibration
- Where to gear up information technology?
What is drive shaft?
Source
First and foremost, there seem to be some conflicting ideas about what is a "drive shaft". We'd like to clarify that.
Co-ordinate to Wikipedia, drive shaft is a mechanical component for transmitting torque and rotation. Information technology'southward a perfectly accurate definition only the merely problem is that it is very broad definition. If you Google the give-and-take "bulldoze shaft", y'all volition see a lot of unlike pictures of (i) propeller shaft or (ii) Cardan shaft or even (iii) universal articulation shaft. All of which are collectively known equally drive shaft by international standard.
Merely these are Non the drive shaft that we will be talking about today.
I'll explain why.
In Malaysia, we have our own local lingo. The universal joint shaft is what nosotros Malaysian would call a "long shaft" because of the length of the shaft. On the other hand, we refer to what is known every bit "one-half shaft" internationally as "bulldoze shaft" instead.
This is not a word of who's right or incorrect, but to establish a common set of definition so that we will be on the same page when we talk nearly "drive shaft" in the following section.
In brusque, the motion-picture show in a higher place is what we volition be talking about today.
Broadly speaking, you will be able to find at least two drive shaft for your machine . Depending on your car model, you tin can find the bulldoze shafts next to your forepart wheels or rear wheels or even both (which makes it 4 drive shafts). If you lot climb under your car, you will run into that i end of the bulldoze shaft goes into the car manual, while the other end goes into i of your tyre.
Now that we take that out of the style, let's become correct into information technology.
How does it piece of work?
Then, how does it piece of work and why do we demand it? Drive shafts serve two purpose:
- Improves the range of motion of your car wheels.
Imagine that if your car wheels are connected to the transmission by a rigid metal instead of a drive shaft. When your wheels go over a bump, the wheels will shifts upward but not the transmission. With plenty forcefulness, it will snap the rigid metal in half. That's precisely why we accept bulldoze shaft. It improves flexibility and gives the car wheels a greater range of motion to work with. - Transfers rotational energy from the transmission to the wheels.
When you crank your engine, the engine combusts the petrol-air mixture. The estrus energy gets converted into kinetic energy which pushes the motorcar engine pistons up and down. Subsequently, the car manual then harvests this engine power and converts them into rotational energy through a differential. When the differential rotates, it passes the rotation through the drive shaft and so to your motorcar wheels. Finally, as your car wheels start to roll, your car moves frontward.
Every bit you can see, drive shaft is a very important function of your car. If yous remove it, your automobile won't motion! That'due south why nosotros call it… drive-shaft, because it's a flexible shaft that drives the bike.
"Drive shaft, drives y'all forward"
What is the pinnacle iii bulldoze shaft bug?
Mechanical parts, especially moving ones are decumbent to vesture and tear. Drive shaft is no dissimilar. We have compiled and isolated the top iii drive shaft problems and we are hoping to share it with you today.
ane. Spoiled or torn drive shaft embrace
A drive shaft cover / constant velocity boot is this blackness color rubber-like cloth on your drive shafts. Information technology's main purpose is to keep contaminants away, and the lubricating grease inside the constant velocity joint .
A torn comprehend can be detected very easily if you know where to wait. All you need to do is put on some dirty clothes, clamber under the car and locate your drive shaft. You will find a visible crack or a puncture at the drive shaft comprehend. Most of the time, this volition exist accompanied past grease splashes effectually your car tyre.
If y'all have a spoiled comprehend, nosotros recommend that y'all get it changed immediately. Forget about groceries, forget about your laundry, you can do your dishes afterwards but don't wait on the repair.
Here'due south why we're making such a big deal out of this.
Fact is that the bulldoze shaft cover is the just line of defense for your drive shaft. It keeps the lubricating grease in, and the wet and clay out.
For drive shafts and any moving parts really, it is always important to have lubricating grease. Information technology cushions and reduces metal-to-metallic contact within the constant velocity articulation. Think of them like airbags. The brawl bearings inside of your drive shaft is better off hitting a soft textile rather than banging direct-on to the metallic wall. Without the lubricating grease, the metal will commencement collide confronting each other and vesture out significantly faster.
To make matter worst, when the constant velocity kicking is torn, information technology opens upwardly opportunity for moisture and dirt to get into your drive shaft. When wet make it contact with metal, it will start to course rusts and swallow into your metal. Needless to say that it ruins the structural integrity of your drive shaft. Dirt and sand on the other mitt, volition grind against the metal part of your drive shaft and wear out your drive shaft way faster than it should. It's like having sandpaper inside the constant velocity articulation, definite a large no-no.
Nosotros hope nosotros don't sound bias because we practice repair drive shaft. Just, nosotros hope that you see the reasoning and the value of detecting and repairing it earlier. Depending on how early on you become it repair, it can mean huge savings on your machine maintenance bill.
If the drive shaft is still in pristine condition, other than the fact that the cover bankrupt, y'all can but put in new grease, and supersede the encompass. It's a simple repair and will cost you way lesser than replacing the entire unit. This is the single most important and toll-effective way of maintaining it .
Although I do have to say that it is easier said than washed because when yous have a spoiled or torn drive shaft cover, it often go unnoticed. Why? Because a torn drive shaft cover does not show any symptoms other than the puncture itself. When nosotros practise not modify the cover, the drive shaft deteriorate at an exponential rate and you volition start to notice racket and vibration.
It's similar a ticking time bomb!
That beingness said. If you are determined enough, you tin do a routine inspection once every week or and then. As shortly every bit y'all find out that you lot have a torn cover, phone your foreman immediately to become it serviced.
2. Clicking Noise
Flick this.
You are driving on the road trying to get to work. Then, you see a sharp turn to the left in forepart and so you first to steer your motorcar to that direction. All of a sudden, you hear this rapid clicking noise when turning.
Although some car models can differ slightly, this is the near obvious sign of a drive shaft failure.
That is a tell-tale sign for y'all to know that y'all have a bad bulldoze shaft.
The clicking noise is an audible noise that sounds like "tak tak tak…" and information technology goes on as long as y'all are turning. It is especially noticeable when you are turning a sharp corner. Fifty-fifty more and so when you step on the gas pedal when turning.
Let's take a closer await.
Yup, definitely a worn CV axle.
Yous should be able to hear it from your driver seat when driving. If yous listen close enough, you lot can hear which side is the noise coming from. In the hands of an experienced car mechanic, they tin even tell if it's coming from both side or just one side.
What should you exercise if you lot hear the clicking noise?
Well, in that location is no easy way to say this. Only if you lot can hear it, it ways that you definitely need a drive shaft repair.
You can consider replacing the front wheel drive axle yourself but we practice not recommend that unless you lot know your manner around auto repair. This is because there are a zillion things that could become wrong. Too, labor charges are only between RM thirty ~ RM 70 per bulldoze shaft. Given the gamble and time required, information technology's just non worth it to learn and execute it yourself.
Merely if you would really dear to DIY it, here'due south a slap-up video to give you lot an thought of what you demand to do. I'd like to bespeak out that this is not an absolute guide and is only intended to betoken you towards the correct direction. You should always practice circumspection and consult a professional if y'all are not sure.
Alternative, you can get someone else to do the hard work for you. Only head over to the nearest motorcar workshop to get a professional person to inspect and change information technology for you. Most workshop volition take no problem providing this service. If you happens to be in Petaling Jaya expanse, you tin can always call us!
Lastly, we would recommend getting both your bulldoze shaft repaired. This is because if one side is worn, most probable the other one will exist as well. Ii is ever amend than i. This'll relieve you a trip to the local car service eye in the future!
iii. Vibration
It'southward Saturday morning and you've planned a field trip together with your friends. You've been looking forrad to this day and it's finally hither! As you turn into the highway, you outset to accelerate at xxx… 40… 50… threescore kilometers per 60 minutes. It was this moment that you start to feel your steering cycle shaking when you accelerate .
Gauge what? You've just found out that you have a bad drive shaft. Non exactly a neat way to boot start your weekend.
A bad one-half shaft can cause vibration at your steering wheel when travelling at low to medium speed. We are talking about roughly in the range of 50 kilometers per hour .
However, don't simply rush to a nearby drive shaft shop to buy yourself a reconditioned part just yet. You may end up ownership something that you don't need. This is because vibration is a common symptoms and can be caused by many other things. For case:-
- Engine mounting
- Worn out long shaft
- Out-of-circular rims
- Unbalanced tyres
- Poor road weather condition
Well, if you notice the vibration, what should you practise?
We strongly recommend that you get a professional test drive done to see if it is really a worn bulldoze shaft. Once confirmed, you should get your drive shaft repaired before it gets worst.
If the vibration is left unattended, the wear will deteriorate aggressively .
Instead of a straightforward repair, it can go a complicated one. Or worse, you may have to pay for a new one which will costs a fortune. You know what they say, early birds save tons of coin (or something similar that).
The Bottom Line
We discussed about what a bulldoze shaft is, and how it works. A bad drive shaft causes unpleasant driving experience such as dissonance and vibration while compromising your prophylactic. By now, yous already know the symptoms of a bad drive shaft, how you tin can identify and why you should get information technology fixed a.southward.a.p. Some say that there are no free dejeuner in the world. But I say that repairing your drive shaft early is as close as it gets.
If y'all have a worn drive shaft and happens to live in Selangor, Malaysia… Make it touch with united states of america! Equally a bulldoze shaft & steering rack specialist who have been in the manufacture for close to 3 decades, y'all can be residuum bodacious that your car volition exist in good hands.
Until and then, bulldoze safe and drive smart!
Source: https://dsauto.com.my/en/2018/10/29/common-drive-shaft-problems/
0 Response to "How to Remove Rear Drive Shaft on Can Am Outlander"
Post a Comment